Concrete surface reinforcement agent

(Concrete rebound strengthening agent)

Product features:

1. This product is non-toxic, odorless, and environmentally friendly. It undergoes a chemical reaction with concrete infiltration to form dense crystals. Easy to construct, just spray and brush to achieve ideal wear resistance, hardening, and brightening effects;

2. Penetration curing: effectively penetrates 1-30mm, reacts chemically with substances in the concrete, and forms a dense whole; Improve compressive strength by 10% -25%, effectively increasing hardness and density;

3. This product is a high-tech product developed in collaboration with universities and produced using German technology. Its effective ingredients can quickly react with the free calcium and other chemical components in the concrete, which can not only generate gel, but also generate some stable silica calcium hardening substances, increasing the density of the structure, making the concrete surface form a solid solid as hard as a chimestone, greatly improving the strength, hardness and wear resistance of the concrete structure surface, so as to obtain a permanently closed, solid, wear-resistant, dust-free, water resistant and resistant to most industrial chemicals. Make the cement concrete floor with poor surface strength, graying, and sanding hardened to completely no sanding or graying.

Advantages: 1. Simple construction without affecting other secondary constructions.

2. It will not increase the height or thickness of the operating surface

3. Rapid onset: usually takes 1-3 days to take effect, and stabilizes after reaching the optimal value a week later.

Scope of application:

1. Painting new and old concrete floors, walls, and columns to increase strength and hardness can generally increase rebound values by 10% -25%. After 7 days of hardening, the hardness can increase by 40%.

2. Reinforcement and repair treatment of cement and concrete floors with various types of dust, ash, and sand.

3. Various types of new and old concrete floors, cement floors, terrazzo floors, and post-treatment after dust and sand removal to improve hardness and wear resistance;

4. The surface strength of various new concrete components and cement products is insufficient for painting, which increases the strength and hardness. Extend the service life.

usage method:

1. Before formal use, it is recommended to conduct on-site small-scale tests to confirm the effectiveness and dosage before large-scale use. (Please stir evenly before application. If there is any sediment, please stir well before use to ensure that it does not affect the effectiveness of use.)

2. Surface cleaning: First, remove the demoulding oil, oil stains, floating dust and other garbage. Depending on the surface condition, an appropriate amount can be used

Pre treatment methods such as rinsing with clean water or sanding with fine sandpaper can significantly improve the strength of concrete. If there is release oil or floating slurry, sandpaper or wire brush should be used to remove the release oil or loose floating slurry from the concrete surface, otherwise it will directly affect the use effect.

3. Brush and roll apply this product, maintaining a saturated and moist state for 30 minutes each time. The longer the time, the better the effect. The most crucial step is that the longer this time, the better the concrete absorbs and the higher the strength it increases, so that more effective ingredients can enter the interior of the concrete.

4. Generally, spraying twice is sufficient, and the second coat should be applied 8-12 hours after the first coat (depending on weather conditions). Based on the actual strength of the concrete, it is recommended to use a total amount of 3-5 kilograms per square meter for two passes. If the effect is not significant after the second coat, it indicates insufficient absorption, and the material can be brushed or rolled again.

5. Maintenance: After the second spraying is completed, when the water evaporates or no visible water is visible, spray a small amount of water in a timely manner to keep it moist, and the whole time lasts about 4 hours.

6. The construction environment temperature is between 5-50 ℃, and the optimal temperature is between 5-32 ℃.

7. The treated concrete takes 1-3 days to take effect and reaches its optimal level within 5-7 days

Specification parameters:

1. Appearance: Water based liquid

2. Usage: Based on the condition of the base layer, it is generally determined to be 3-5 square meters per kilogram (for floors, facades, and flat surfaces, the best effect is achieved, and concrete is more easily absorbed)

3. 3. Packaging: This product is packaged in 25L and 50L containers.

Save method:

Store in a cool and dry place, with a temperature not exceeding 50 ℃. Seal the bottle tightly and seal the bottle mouth promptly after each use.

matters needing attention:

After one week of construction, the ground should not come into contact with water. During construction, gloves and other personal protective equipment should be worn to avoid contact with the skin and eyes. If accidentally entering the eyes, please rinse with water or see a doctor. After each use, please seal the bottle mouth.